自干免烘烤金属油墨

自干免烘烤金属油墨

品牌：欧莱斯

适用对象：金属，玻璃，陶瓷，电镀，五金，不锈钢，铝合金，拉丝面板

单件净重：1公斤

着色力：100

细度：0.01

粘度：1500s

流动度≥：100

保质期：72个月

型号：mpl

用途：1.适用范围:铁、铝、合金、玻璃、陶瓷、电镀、石材、阳极氧化铝表面及烤 （喷）漆面等2.稀释剂  :用本公司s-03稀释剂  3.固化剂  :可添加ta-9154硬化剂  10％增加附着力,提高墨膜硬度。

耐温性：低温玻璃油墨

性能：自干玻璃漆

供应玻璃油墨基本信息

本产品是采用高级进口丙烯酸  树脂和高级颜料经过细制研磨加工组合而成，用于各种金属、玻璃、陶瓷、石材、电镀(含水电镀)、阳极氧化铝表面及烤（喷）漆面等制品的丝印及移印，不需加固化剂  ，不需烘烤，即可获得优异的附着力。

油墨特性：

1、平光、附着力佳、耐汽油、耐化学品；

2、手感好，流平性佳、面光洁；

3、表面硬度好，耐冲击性能强、抗刮伤；

4、耐汽油、耐酒精、耐化学品程度佳；

印刷：

选用网目为100-350目，以120t网纱计算涂覆盖面积每公斤达30~35㎡。

表干时间自然挥发5-15分钟，实干时间在24小时以内，48小时后达最佳性能。

1．用配套专用稀释剂  开油水

2．用718洗网水洗网。

3．或添加配套硬化剂  10％可增加附着力,提高墨膜硬度。

4．烤箱80℃烘烤10分钟佳能更优。

测试方法（完全干燥后）：

1．3m胶纸粘在画有百格的油墨表面45度角迅速拉起不脱油。

使用方法：

1．建议用我公司专用稀释剂  进行稀释，不建议使用783慢干稀释剂  稀释，使用前应充分搅拌，用后随时密封。

2．搅拌时加本公司配套开油水10-12％，稀释到印刷适合粘度，移印稀释使用移印专用稀释剂  ；用718洗网水清洗。

3．不得与其它类型油墨混合使用，否则容易出现其他附着力，化学反应等不良现象。

4. 加入固化剂  的油墨使用时限为8小时，过期请弃用，剩余油墨不可回收

注意事项：

1．各种承印物料的外观相似，但可能会是不同的材料，客户需先试印，确其符合要求后，再批量生产。

2．在移印过程中，如出现拉丝或散开，可适当加入一些慢干膏即可;

3．环境温度过高，将会影响油墨原有质量。白色超越150都会变色，烘烤时请用木质材料垫底进行烘烤，不得直接接触铁

4．根据气候变化，请远离火源，阴暗处15度-30度环境下存放。

brand: oleser

applicable objects: metal, glass, ceramic, electroplating, hardware, stainless steel, aluminum alloy, drawing panel

net weight: 1 kg

tinting power: 100

fineness: 0.01

viscosity: 1500s

flow degree is larger than 100

shelf life: 72 months

model: mpl

purpose: 1. scope: iron, aluminum, alloy, glass, ceramics, stone, electroplating, anodic alumina surface【敏感词】baked (spray) 2. paint thinner: with the company s-03 diluent 3.: add ta-9154 curing agent hardening agent 10％ increased adhesion, improve the ink film hardness.

temperature resistance: low temperature glass ink

properties: self drying glass paint

basic information for glass ink

this product is the use of advanced import acrylic resin【敏感词】senior pigment after fine grinding system combination, all kinds of metal, glass, ceramic, stone, used for electroplating (aqueous electroplating), anodic alumina surface【敏感词】baked (spray)【敏感词】silk screen printing products such as paint, without curing agent,【敏感词】does not need to bake, can be obtained excellent adhesion.

ink characteristics:

1, matt, adhesion, petrol, chemical resistance;

2, feel good, leveling good, smooth surface;

3, surface hardness, impact resistance, scratch resistance;

print:

the mesh is 100-350 mesh, 120t mesh with coverage area calculation per kilogram of 30~35 square meters.

table dry time natural evaporation 5-15 minutes, work time in less than 24 hours, 48 hours after the best performance.

1., with a dedicated diluent to open oil【敏感词】water

2. wash net with 718 washing nets.

3.【敏感词】add matching hardening agent 10％, increase adhesion, improve ink film hardness.

4. oven 80 degrees baking 10 minutes, canon is better.

test method (fully dry):

1.3m tape is glued to the surface of the ink that has a hundred squares,【敏感词】the 45 degree angle is pulled rapidly without oil removal.

usage method：

1., i suggest using my company's special diluent for dilution, do not recommend using 783 slow dry diluent dilution, before use should be fully agitated, after use at any time sealed.

2. add the company supporting stirring open water 10-12％, diluted to printing for viscosity, printing the dilution used printing special thinner; use clean water to wash the nets 718.

3.,【敏感词】other types of ink may not be mixed use, otherwise prone to other adhesion, chemical reactions【敏感词】other undesirable phenomena.

4., the use of curing agent ink, the use of time limit is 8 hours, expired please abandon,【敏感词】the remaining ink can not be recycled

matters needing attention：

1., the appearance of a variety of printing materials similar, but may be different materials, customers need to try to print, to ensure that they meet the requirements,【敏感词】then mass production.

2. in the pad printing process, such as drawing【敏感词】spreading, you can properly add some slow dry paste can be;

3. environmental temperature is too high, will affect the original quality of ink. white over 150 will change color. when baking, please use wooden material at the bottom of baking, not direct contact with iron

4., according to climate change, please stay away from the fire, dark place, 15 degrees -30 environment storage.