欧莱斯pp系列油墨是采用进口原材料及颜料经技术中心反复测试调制而成的pp免处理高性能油墨，油墨墨层柔软度好、富弹性、耐磨损，对于未处理pp料通用性好，具有_耐热油、耐汗液、高抗刮性、高耐醇、高耐磨、耐水煮、流动性好，可丝印和移印等特点。
【适用材料】
pp料、处理过之pe料、尼龙料及类似材料
【产品举例】
玩具、洗发水瓶、化妆品瓶、奶瓶、水杯、果汁机_、豆浆机_、洗碗机_等
【基本性能】
承印物：未处理的半透明pp水杯、印刷后自干24小时测试检测项目测试方法、条件测试结果酒精测试用加载500克力的粘酒精（99.7％）棉布来回平推100次不露底附着力测试百格法：划1mm×1mm #格 用3m胶纸以90度直角剥离5次无脱落耐摩擦用加载500克力的普通橡皮来回平推100次不露底耐火机_油用加载500克力的粘机_油棉布来回平推30次不露底耐水煮100℃煮1小时仔细观察，印刷字体和图案颜色无变化【使用说明】
网板：250—350目聚脂丝网印版胶刮：建议使用65-80度聚氨酯胶刮参考用量：300目网板印刷约为35㎡/㎏选用稀释剂 _：s-91丝印稀释剂 _、s-81移印稀释剂 _网板清洗：选用有_机_溶_剂 _清洗（如：洗网水）
【干燥条件】
自然挥发干燥：表干5分钟，完全干燥48小时或者烘烤85-100℃ 40分钟（烘烤温度较高时，可适当减少烘烤时间）pe料、尼龙料、有_添加口水杂料或有_蜡层的pp料建议烘烤附着性更佳。
【固化剂 _】
对pe料和部分杂料之pp料，可能会出现附着力差等现象，可选用本公司ppa-34处理剂 _擦拭或添加t-2m固化剂 _10％进行加温烘烤，以增强其附着力。
【注意事项】
1、塑胶产品具有_多样性，材料外观相似但可能是不同的材料，建议做好测试再进行印刷
2、对于表面张力较小的材料，可先用pp处理剂 _或火焰处理法对底材进行处理后印刷，这样可以提高油墨的附着力。
3、该油墨属于慢反应固化型油墨，测试附着力必需在印刷后24小时以上再进行测试。
4、pp油墨显酸 性，用于移印时，如果油墨长时间浸泡覆盖钢板可能对钢板有_轻微的腐蚀。
5、银色、金色建议低温（10℃以内）保存，在常温下保存的时间相对较短，一般不超过1个月。
pp series of ink is the use of imported raw materials【敏感词】pigment by the technology center of repeated testing of modulated pp free high performance ink, ink layer, good softness, flexibility, abrasion resistance, for the untreated pp material has good universality, is heat oil, sweat resistance, high scratch resistance, high alcohol, gao nai wear resistance, boiling water resistance, good fluidity, screen printing【敏感词】pad printing etc..
[applicable materials]
pp material, treated pe, nylon【敏感词】similar materials
[product example]
toys, shampoo bottles, cosmetic bottles, bottles, water cups, juice machines, soya bean milk machines, dishwashers, etc.
[basic performance]
substrate: untreated translucent pp cup, printed after 24 hours of dry test
test item
test methods【敏感词】conditions
test result
alcohol test
with 500 grams of alcohol loaded adhesive (99.7％) to push back cotton
do not open at the end of 100
coating adhesion test
100 lattice method: row 1mm * 1mm # lattice with 3m tape to a 90 degree angle off 5 times
no shedding
friction resistance
by loading 500 grams of ordinary rubber to push back
do not open at the end of 100
fire-resistant oil
with sticky cotton oil loading 500 grams【敏感词】flat push
do not open at the end of 30
boiling resistance
cook for 1 hours at 100
close observation shows no change in the color of the print【敏感词】pattern
[instructions for use]
mesh plate: 250 - 350 mesh polyester screen plate
squeegee: it is recommended to use 65-80 degree polyurethane squeegee
dosage: 300 mesh screen printing is about 35 kg / square meters
choose thinner: s-91 screen thinner, s-81 printing thinner
screen cleaning: the use of organic solvents cleaning (such as: washing mesh water)
[drying conditions]
natural dry: dry for 5 minutes, completely dry 48 hours【敏感词】40 minutes (c 85-100 baking baking temperature is high, may be appropriate to reduce the baking time) pe material, nylon material, adding complex material【敏感词】pp material slobber suggest baking wax layer adhesion.
[curing agent]
for pe materials【敏感词】some miscellaneous materials of pp material, there may be poor adhesion,【敏感词】so on, we can choose our company ppa-34 treatment agent to wipe【敏感词】add t-2m curing agent 10％ for heating baking, so as to enhance its adhesion.
[matters needing attention]
1, plastic products are diverse, similar material appearance, but may be different materials, it is recommended to do the test【敏感词】then print
2, for the less surface tension of the material, you can first use pp treatment agent【敏感词】flame treatment method for the substrate after processing printing, so as to improve the adhesion of the ink.
3, the ink belongs to slow response curing ink, test adhesion must be printed after more than 24 hours【敏感词】then tested.
4, pp ink acid, used for pad printing, if the ink for a long time to cover the steel plate, may have slight corrosion of steel plate.
5, silver, gold, recommended low temperature (10 degrees celsius) preservation, at room temperature preservation time is relatively short, generally not more than 1 months.
免费会员